Product video:
Our COMAX® software
»
The Dreika K1 is used with upright reinforcement. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 is used with upright reinforcement. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
Downloads
The Dreika K1 S is used for vertical reinforcement. S stands for diagonal cut. Two parallel diagonal cuts are made at the factory. This prevents the formwork from touching down and catching. The formwork slides over the slope along the triangular section. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
Downloads
The Dreika K1 N is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 N is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 N S is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. S stands for diagonal cut. Two parallel diagonal cuts are made at the factory. This prevents the formwork from settling and catching. The formwork slides over the slope along the triangular section. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
Dreika K1 N S acid-resistant is mainly used for standing reinforcement in precast concrete pipe plants. The concrete is chemically resistant. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. S stands for diagonal cut. Two parallel diagonal cuts are made at the factory. This prevents the formwork from settling and catching. The formwork slides over the slope along the triangular section. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K2 N is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. Two steel clamps Ø1.5 mm are fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamps ensure very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
Downloads
Dreika K2 N S acid-resistant is mainly used for standing reinforcement in precast concrete pipe plants. The concrete is chemically resistant. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. S stands for diagonal cut. Two parallel diagonal cuts are made at the factory. This prevents the formwork from settling and catching. The formwork slides over the slope along the triangular section. The length of the Dreika is designed for a rebar spacing of up to max. 15 cm. Two steel clamps Ø1.5 mm are fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamps ensure very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 is used with upright reinforcement. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 is used with upright reinforcement. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 S is used for vertical reinforcement. S stands for diagonal cut. Two parallel diagonal cuts are made at the factory. This prevents the formwork from touching down and catching. The formwork slides over the slope along the triangular section. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
Downloads
The Dreika K1 N is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 N is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. A steel clamp Ø2 mm is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K1 N S is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. S stands for diagonal cut. Two parallel diagonal cuts are made at the factory. This prevents the formwork from settling and catching. The formwork slides over the slope along the triangular section. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. A Ø2 mm steel clamp is fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamp ensures very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.
The Dreika K2 N is used with upright reinforcement. N stands for the dimpled contact surface. The dimpled surface means that the spacer is not in full contact with the formwork and is only slightly visible on the concrete surface after concreting. The length of the Dreika is designed for a rebar spacing of up to max. 27 cm. Two steel clamps Ø1.5 mm are fitted at the factory. The Dreika can be mounted on reinforcing steel Ø 6-14 mm. The clamps ensure very quick installation. Thanks to its fastening and elongated shape, the Dreika is tilt-proof and stable.