Product video:
Our COMAX® software
»
Made from weldable and bendable BETOMAX® tie rods 15, 20 and 26.5
For one-ended anchoring in concrete
For use as lost (internal) tie rod
Also for use in conjunction with cones, e.g. for climbing formwork
For one-ended anchoring in concrete
For use as lost (internal) tie rod
Also for use in conjunction with cones, e.g. for climbing formwork
Downloads
Made from weldable and bendable BETOMAX® tie rods 15, 20 and 26.5
Same applications as pigtail anchor, but also for smaller wall thicknesses
Same applications as pigtail anchor, but also for smaller wall thicknesses
Made from weldable and bendable BETOMAX® tie rods 15, 20 and 26.5
For anchoring supports, for single-sided formwork
Installed in first concreting section, in floor slab
Can be extended with threaded connecting sleeve and MKK®
For anchoring supports, for single-sided formwork
Installed in first concreting section, in floor slab
Can be extended with threaded connecting sleeve and MKK®
Downloads
The finishing cone for the perfect concrete surface.
Made of plastic. For use with MKK® when installing at 45°.
Downloads
Steel strip and plastic sleeve for anchoring aids for single-sides wall formwork.
For installing tie rods, anchor loops, pigtail anchors, round hooks etc. at 45°.
Thread Ø d1
B 15 25
B 20 32
B 26.5 40
Working example:
Illustrated with anchor loop
L = Projection for fastening with threaded connecting sleeve
Thread L
B 15 70
B 20 80
B 26.5 100
For installing tie rods, anchor loops, pigtail anchors, round hooks etc. at 45°.
Thread Ø d1
B 15 25
B 20 32
B 26.5 40
Working example:
Illustrated with anchor loop
L = Projection for fastening with threaded connecting sleeve
Thread L
B 15 70
B 20 80
B 26.5 100
Downloads
Suitable for use as a one-sided anchoring.
Typically used for climbing formwork, scaffold anchors and thin-walled structures.
Consists of bendable and weldable B 15 threaded tie rod and plate (90 x 120 x 10 mm).
Vt = Anchoring depth
Et = Installed depth
Rod failure at max. tensile load
Typically used for climbing formwork, scaffold anchors and thin-walled structures.
Consists of bendable and weldable B 15 threaded tie rod and plate (90 x 120 x 10 mm).
Vt = Anchoring depth
Et = Installed depth
Rod failure at max. tensile load
Casting, for one-sided anchoring. Max. load depends on the concrete quality and anchoring depth (Vt). Compatible with Uni 15.
Concrete quality C 20/25
VT = 20cm
for 90 kN working load
Concrete quality C 20/25
VT = 20cm
for 90 kN working load
Downloads
Made from an anchor plate with welded-on B 20 hexagon nut. For one-sided anchoring. Compatible with Uni 20.
Vt = Anchoring depth
Et = Installed depth
Anchoring depth: Vt = 175 mm
(Acc. to test certificate, failing load in concrete 177 kN and concrete quality C20/25)
Failing load in concrete:
235 kN in uncracked concrete
177 kN /181 kN in cracked concrete
(test cone dia. restricted to 850 mm)
Concrete strength: 30 N / mm²
Max. load depends on the concrete quality and anchoring depth (Vt)
Vt = Anchoring depth
Et = Installed depth
Anchoring depth: Vt = 175 mm
(Acc. to test certificate, failing load in concrete 177 kN and concrete quality C20/25)
Failing load in concrete:
235 kN in uncracked concrete
177 kN /181 kN in cracked concrete
(test cone dia. restricted to 850 mm)
Concrete strength: 30 N / mm²
Max. load depends on the concrete quality and anchoring depth (Vt)
Casting for one-sided anchoring.
Vt = Anchoring depth
Et = Installed depth
Max. load depends on the concrete quality and anchoring depth (Vt)
Vt = Anchoring depth
Et = Installed depth
Max. load depends on the concrete quality and anchoring depth (Vt)
For securing single-sided formwork in concrete or rock walls. Comatible with Uni 15. Also for attaching ledge consoles to components without concreted-in anchoring parts, e. g. when renovating existing structures.
Conduct tensile test before applying final load
Test load can be applied with BETOMAX® rock anchor testing device
- please ask for details
Conduct tensile test before applying final load
Test load can be applied with BETOMAX® rock anchor testing device
- please ask for details
Forged weld-on part with fillet weld.
a = 4 mm. Weld on all round.
Steel quality: S 355 (St 52-3) with tapped thread. Comatible with Uni 15.
Weld seam´s compliance with DIN 18800 to be statically verified
a = 4 mm. Weld on all round.
Steel quality: S 355 (St 52-3) with tapped thread. Comatible with Uni 15.
Weld seam´s compliance with DIN 18800 to be statically verified
Downloads
For tie rods B 15. Compatible with Uni 15.
Weld seam´s compliance with DIN 18800 to be statically verified
Not for use as connecting sleeve
Weld seam´s compliance with DIN 18800 to be statically verified
Not for use as connecting sleeve
For welding at inclinated areas, e.g. sheet pile walls.
For one-sided anchors at sheet pile walls
Vertical 90° orientation between inclinated anchoring point and formwork
For one-sided anchors at sheet pile walls
Vertical 90° orientation between inclinated anchoring point and formwork
Downloads
Befestigungsteil mit metrischem Gewinde, Verschluss mit Stopfen 20.
Downloads
For securing push-pull props and BETOMAX® curb shuttering, galvanized.
The BETOMAX® K-TEC-3s© can be reused several times and combines the benefits of a coarse thread for temporary machine fastening with those of a self-tapping concrete screw.
Numerous applications
Suitable for all temporary fastening requirements for low to medium loads, e.g. for fastening machines such as core drilling and concrete finishing machines etc.
Both: Rugged B15 formwork tie thread
Facilitates the use of all types of screwed fastening: Kipp B15 with hex nut, waler wing nut or similar
And: High-strength, self-tapping special thread
For reliable, positive anchoring in the concrete
Easy procedure
Supremely simple system with minimal number of components
Enormous time saving
Drilled hole does not need cleaning; no additional work procedures
For installing close to edge and to each other
No plugs, no expansion
Resists high loads
Thanks to perfect positive fit in the concrete
Minimal tooling
Cordless screw driver recommended
Very simple inspection
Check the hole diameter (14 mm) and depth, and ensure that the bolt is tight
Reusable
Depending on surface conditions, up to 20 stress actions possible. Simple control due to checking gauge (has to be ordered separately)
Numerous applications
Suitable for all temporary fastening requirements for low to medium loads, e.g. for fastening machines such as core drilling and concrete finishing machines etc.
Both: Rugged B15 formwork tie thread
Facilitates the use of all types of screwed fastening: Kipp B15 with hex nut, waler wing nut or similar
And: High-strength, self-tapping special thread
For reliable, positive anchoring in the concrete
Easy procedure
Supremely simple system with minimal number of components
Enormous time saving
Drilled hole does not need cleaning; no additional work procedures
For installing close to edge and to each other
No plugs, no expansion
Resists high loads
Thanks to perfect positive fit in the concrete
Minimal tooling
Cordless screw driver recommended
Very simple inspection
Check the hole diameter (14 mm) and depth, and ensure that the bolt is tight
Reusable
Depending on surface conditions, up to 20 stress actions possible. Simple control due to checking gauge (has to be ordered separately)
Downloads
K-TEC-MS© from BETOMAX® systems is used for one-sided anchoring in existing concrete substrates.
Load data:
characteristic pull-out values for C 20/25 = 28.9 kN (according to test certificate no. 213000080-19 de MPA NRW)
Load data:
characteristic pull-out values for C 20/25 = 28.9 kN (according to test certificate no. 213000080-19 de MPA NRW)
Downloads
For one-ended anchoring with BETOMAX® 15. Manufactured from fibre-reinforced plastic.
CLIMAX® anchoring sleeve
Typical applications: bridge floor edge shuttering, consoles, scaffolding and single-sided formwork.
CLIMAX®-Fifty anchoring sleeve
Shallow installed depth of 51 mm (sleeve) and 12 mm (nailable cap) for precast concrete cavity walls.
CLIMAX® anchoring sleeve
Typical applications: bridge floor edge shuttering, consoles, scaffolding and single-sided formwork.
CLIMAX®-Fifty anchoring sleeve
Shallow installed depth of 51 mm (sleeve) and 12 mm (nailable cap) for precast concrete cavity walls.
Die Climax ST® - Verankerungshülse ist für den Einsatz von einseitigen Verankerungen mit Betomax 15 Schalungsankern vorgesehen. Sie findet ihren Einsatz bei Deckenrandabschalungen, Konsolen, Gerüsten, einhäuptiger Schalung bei geringerem Schalungsdruck.